AUDI Recalls

2019–2024 AUDI Q7, Q8 e

Due to a manufacturing issue, the modules installed in the high voltage battery may be defective. During charging a thermal overload could result in a vehicle fire.

2024–2025 AUDI RS6

On certain vehicles, the front passenger airbag may have been damaged in transit prior to installation in the vehicle.

2021–2023 AUDI Q5

Due to a manufacturing issue, the modules installed in the high voltage battery may be defective. During charging a thermal overload could result in a vehicle fire.

2020–2024 AUDI e-tron GT, RS GT

Due to a manufacturing issue, the front axle brake hoses may deteriorate over time. If this occurs, it could lead to a brake fluid leak resulting in reduced braking performance.

2020–2024 AUDI e-tron GT, RS GT

Due to a manufacturing issue, the cell modules installed in the high voltage battery may be defective. A short circuit could cause a thermal overload and result in a vehicle fire over time. The potential defect can be determined with an initial check.

2018–2022 AUDI E-Tron 55, 55 Sportback

Due to a manufacturing defect, the high voltage battery may experience a thermal overload if charged over 80 percent capacity. If this occurs, the battery could overheat and lead to a vehicle fire.

2023 AUDI Q7, Q8

Due to a manufacturing defect, the front passenger airbag may not have been installed correctly.

2022–2023 AUDI e-tron GT

Due to a manufacturing issue, the sealing of the high-voltage battery housing may reduce overtime, allowing moisture to enter. The moisture may potentially result in an electrical short circuit increasing the risk of fire.

2023 AUDI A4, A5, Q3, TT, Q7, Q8

Due to a manufacturing defect, the outer backrest frame of the front seats may have been incorrectly welded. As a result, the seat frame could fracture.

2019–2023 AUDI A3, Q2

Due to an installation defect, the internal fuse box wiring harness may become loose. If this occurs, the instrument cluster may fail to illuminate, internal, external lamps may switch off, and the vehicle may experience a sudden loss of motive power whilst driving. Note: In an event of failure, the driver will be able to steer and apply the brakes.

2023 AUDI TT

The welding connection joining the airbag guide channel and the dash panel of the front passenger’s side, may not meet manufacturing specifications. As a result, the front passenger’s airbag may not deploy as intended.

2018–2022 AUDI A6, A7

Due to a manufacturing defect, the indicator that shows the fuel level may not work as intended. This may result in an incorrect display of fuel level and therefore the driver may not be aware when the fuel tank becomes empty.

2018–2022 AUDI A6, A7

Due to its installation position, if there is liquid or liquid droplets spilt on the rear seat bench the control unit for network management may become damaged and fail. A failure of the electronic control unit may have various effects on the vehicle functions. Restricted functions are indicated by warning messages in the instrument cluster. Possible restricted functions could be: Engine – The engine enters emergency running mode and continues running with reduced performance. Gearbox – The automatic gearbox interrupts the power flow in the drive train. Steering – The steering reduces the steering assistance in stages; it may therefore be necessary to use more force to turn the steering wheel as the vehicle slows down.

2018–2021 AUDI Q7, Q8

Due to a manufacturing defect, the fuel delivery unit inside the fuel tank may break. If this occurs it could result in the broken pieces damaging the fuel delivery system. This may cause a sudden loss of motive power. Note: This issue may cause the emission control system warning lamp to light up.

2022 AUDI Q3

Due to a manufacturing defect, the rear window glass may have been manufactured out of specification. This may result in uneven stress distribution causing the window glass to break.

2021–2022 AUDI A1

Due to a manufacturing defect, the seat belt monitoring system may not indicate the seat belt status of the occupants as intended. As a result, there may not be a warning when the passengers do not fasten their seat belts.

2012–2017 AUDI A6, A7, A8

Due to a manufacturing issue, the oil supply in the oil strainer to the turbochargers may become clogged and affect engine operation.

2019–2021 AUDI A4, A5, A6, A7, A8, Q5, Q7, Q8 and e-tron

The previous replacement of the rear axle clamping nuts (as part of the recent recall REC-001665) may have caused a misalignment of the rear axle assembly. This could result in excessive wear to the rear tyres, and may result in a sudden flat tyre and subsequent loss of vehicle control.

2016–2021 AUDI Q5

Due to its installation position, if there is liquid or liquid droplets spilt on the rear seat bench the control unit for network management may become damaged and fail. A failure of the electronic control unit may have various effects on the vehicle functions. Restricted functions are indicated by warning messages in the instrument cluster. Possible restricted functions could be: Engine – The engine enters emergency running mode and continues running with reduced performance. Gearbox – The automatic gearbox interrupts the power flow in the drive train. Steering – The steering reduces the steering assistance in stages; it may therefore be necessary to use more force to turn the steering wheel as the vehicle slows down.

1999–2001 AUDI A4, A6, A8, TT and Audi Cabriolet

Affected vehicles may be fitted with a Takata NADI 5-AT driver airbag inflator that could allow moisture to enter the unit and degrade the airbag propellant. If this occurs, the properties of the propellant may be changed so that the propellant does not react as intended during a collision, causing mis-deployment of the airbag.

2019–2021 AUDI e-tron

Due to a manufacturing issue with a braking component the Anti-Lock Brake System (ABS) and Electronic Stabilisation Control (ESC) function may fail under hard braking.

2019–2021 AUDI Audi A4, A5, A6, A7, A8, Q5, Q8 and Etron

Some nuts fitted to the rear axle assembly did not meet manufacturing specifications and may break. A broken nut may lead to increased movement between the wishbone and hub carrier and a change in the wheel alignment on the rear axle.

2020 AUDI RSQ8

A crack may occur on the cylinder contact surface in the engine, the piston may be damaged or seize during the vehicle’s service life. This could cause the piston to get jammed in the cylinder, which would lead to engine damage. The possibility of the conrod being torn off and the crankcase being pierced, and subsequently of oil escaping, cannot be ruled out, this could result in an engine stall (loss of engine power).

2018–2021 AUDI A4, A5, A6, Q7, Q8

The seatbelt warning (acoustic warning tone and visual display) may occasionally operate rather than continuously, in circumstances such as a seatbelt not fastened or unfastened while the vehicle is moving. If the warning does not sound continuously, a seatbelt may be unbuckled without the driver being informed.

2019–2020 AUDI A6, A7

Due to a manufacturing issue with the vehicle's dash panel, the front passenger airbag may not fully inflate in the event of an accident.

2020 AUDI RS6, Q7, SQ7

A connector may become detached from the crash sensor, which may delay the operation of the side airbag, curtain airbag and/or belt tensioner.

2011–2017 AUDI A8, S8

The engine bay seal may become warped and come loose. If this occurs, engine vibrations may result in the seal making contact with hot components in the engine bay.

2020 AUDI Q5

Due to incorrect welding, the gap on the adjusting mechanism for the backrest of the front seats may be faulty.

2011–2012 AUDI A1, A3, TT

Due to a production fault, over time a crack in the transmission’s pressure accumulator can occur.

2014–2019 AUDI TT

If the vehicle is involved in an accident, a bracket fitted on the vehicle body could collide with the fuel tank, resulting in damage to the fuel tank.

2019–2020 AUDI A4, A5, A6, A7

Moisture may enter via a gap in the housing of the starter-alternator, potentially causing the component to overheat.

0 AUDI Q7, Q8

A gearbox oil pipe may have been incorrectly welded, which can result in a transmission oil leakage.

2007–2016 AUDI A1, A3, TT

Due to a production fault, over time a crack in the transmissions pressure accumulator can occur. Some vehicles were incorrectly assessed as not needing to be repaired.

0 AUDI Q7, SQ7, Q8

The bolted connection between the steering shaft and the steering rack may not be tightened to the required torque, which could lead to the bolted connection loosening.

2018–2019 AUDI Q7

If the airbag is triggered in an accident, the fastener securing an air duct component in the curtain airbag may detach. This may cause the curtain airbag not to inflate sufficiently.

2009–2016 AUDI A8

When the hydraulic system for the power steering is under a high pressure load, or when the steering is in full lock, or if there are heavy vibrations due to uneven road surface, the hydraulic return hose for the power steering may leak.

2018–2019 AUDI A8

The wheel rims on the vehicle do not meet strength specifications. If an affected vehicle hits the kerb or crosses speed humps or uneven road conditions at high speed, the wheel spokes could potentially break.

1997–2000 AUDI A4, A6, A8, TT, CABRIOLET

Affected vehicles may be fitted with a Takata NADI 5-AT driver airbag inflator that could allow moisture to enter the unit and degrade the airbag propellant. If this occurs, the properties of the propellant may be changed so that the propellant does not react as intended during a collision, causing mis-deployment of the airbag.

2016–2020 AUDI Q5

Incorrectly fastened wheel arch covers could come loose over time and potentially detach from affected vehicles.

2018–2019 AUDI A6, A7

Testing has shown that the passenger airbag does not meet the applicable standard. The defects relates to the balance of the trigger times between the belt tensioner and passenger airbag.

2015–2019 AUDI Q5

Incorrectly fastened wheel arch covers could come loose over time and potentially detach from affected vehicles.

2016–2019 AUDI Q5

Wheel arch covers may be incorrectly fastened on some vehicles and may loosen over time.

2014–2018 AUDI Q3

If the vehicle's external front indicator light stops operating over time, the driver may not receive the corresponding warning.

0 AUDI A4, A5

The shock absorber may fail and cause potential separation of suspension components.

2018 AUDI A3

Due to a processing error, the locking pin securing the head restraint may be missing on individual head restraints for the rear centre seat.

2014 AUDI A6 & A7

In the affected vehicles, the auxiliary heater element in the air conditioner may fail, due to an electrical connector that has not been plugged in correctly.

2018–2019 AUDI Q5

The wall thickness of the brake master cylinder may not meet specifications.

2017–2018 AUDI A5

Tyres of the type “Sport Maxx RT Noise Shield 265/30 ZR 20”, which were supplied by the Dunlop company, do not fully comply with the approval test requirements of UN/ECE R30 which was the evidence used to certify to Australian Design Rule ADR 23/02.

2013–2018 AUDI A4,A5 (8K, 8T) 3.0 TFSI

On certain vehicles, it is possible that fuel may escape from one or both fuel rails (low-pressure side).

0 AUDI A5 (F5)

Individual bolted connections on the front axle may not have been tightened to the specified torque.

2018 AUDI A3

A rear seat backrest may be fitted on which the mounting for the head restraint is not correctly welded to the outer backrest frame for the rear seat.

2015–2017 AUDI R8

Audi R8 vehicles could have a possible oil leakage in the gearbox breather when the vehicle is being driven on a racetrack and extreme driving manoeuvres are being undertaken.

2011–2015 AUDI A4, A5 & Q5

The auxiliary heater element in the air conditioner may fail as a result of overheating in the area of the connectors.

2011–2015 AUDI A4, A5, Q5

The auxiliary heater element in the air conditioner may fail as the result of overheating in the area of the connectors.

0 AUDI Q5

The rear brake pistons may have been coated incorrectly, potentially causing increased brake pedal travel and reduced braking effectiveness.

2011–2017 AUDI A4, A5, Q5, A6 & A7

Moisture may enter the electronic components and cause overheating and failure of the additional coolant pump.

2017 AUDI Q5

A defective weld joint that connects the central tube for the dash panel to the chute that helps the airbag inflate correctly may cause the chute to be distorted.

2014–2017 AUDI A4, A5

Part of the aluminium trim strips in the loudspeaker of the front or rear door trim may become detached.

0 AUDI Q3

On affected vehicles, the passenger airbag may not be filled with the required volume of gas. This has occurred due to a production fault leading to a defective weld joint on the gas generator for the airbag.

0 AUDI A3 & Q2

A fault in the manufacturing process for the rear hub carriers has caused a discrepancy in the material hardness. As the durability of the affected hub carriers cannot be assured, there is a possibility that the bolted connections may become detached or the component may fail.

2014–2016 AUDI Q3

On affected vehicles and only when an emergency braking function is initiated via the Electro-mechanical Parking Brake (EPB) button, the brake lights at the rear of the vehicle fail to illuminate. The basic operability of the brakes and brake lights are not affected by this issue when braking via the regular service brake foot pedal.

0 AUDI A4, A5 & A6

On affected vehicles manufactured with a specific period, foreign particles in the coolant may lead to a blockage in the additional coolant pump and cause the pump to overheat.

2008–2009 AUDI A3

A fault in an earth connection on the ESC control unit may occur due to excessive thermo-mechanical strain on components in the control unit.

2010–2016 AUDI Q5

On affected vehicles, if the water drain in the area of the panoramic sunroof is not functioning properly, water can seep into the vehicle’s headliner.

0 AUDI A4, A6, A7, A8

On affected vehicles, there are irregularities in the mix ratio of the igniting agent in some airbag units or belt tensioners which could lead to the airbags/belt tensioners not triggering in the event of an accident.

0 AUDI Q7

On affected vehicles, indentations on the cross piece of the third row of seats were not designed and subsequently manufactured as per correct specifications.

0 AUDI A8

On affected vehicles fitted with the 4.2L FSI engine, leaks may occur in the solenoid valve which controls the gearbox heating circuit.

2007–2008 AUDI A8

On affected vehicles, it is possible that the glass panel is insufficiently bonded to the sliding sunroof frame due to the bonding surfaces not being clean during the production process.

0 AUDI Q5

On affected vehicles, it is possible that the side airbag gas generator housing may eject metal parts if one of the airbags is deployed.

0 AUDI Audi A6 (4GL)

On affected vehicles fitted with Navigation MMI Plus, the MMI was incorrectly coded during production. As a result, the internet content from Google Earth is displayed while the vehicle is moving.

0 AUDI AUDI

The emissions levels may not meet the regulatory requirements when the affected vehicle is driven under normal conditions.

2013–2014 AUDI A3 (8V)

In certain vehicles the fuel delivery pump that supplies fuel to the engine may fail.

0 AUDI A4, A5, A5 CABRIOLET, A6, A7, Q5 & Q7

It is possible that there may be a leak at the fuel rails in the injection system.

0 AUDI A4

The front airbags may not inflate correctly in the event of an accident.

0 AUDI A4,A5,A5 CABRIOLET, A6, A7 & Q5

Engine oil may enter the brake servo via the vacuum lines. If this should happen, the diaphragm in the brake servo can rupture, causing the brake servo to fail.

0 AUDI A1, A3 & TT

On Audi A1, A3 and TT model vehicles with a 7-speed dual clutch gearbox (DSG) manufactured within a specific period, conductive deposits may form in the gearbox control unit (due to electrolysis). These accumulations settle between the conductor paths of the electronics in the form of conductive particles and can therefore cause an electrical short circuit and the gearbox fuse could blow. Should this happen, the clutch will fully open due to power supply failure, causing the vehicle to roll to a stop if in motion.

0 AUDI A8

Audi A8 vehicles with glass sliding/tilting sunroof (PR number 3FE) manufactured within a specific period, an unfavourable stress distribution was set up in the glass roof panel during production. This can cause the glass panel to break unexpectedly. This usually happens when a door is slammed closed while the vehicle is stationary.

0 AUDI S6, RS6 & S7

Audi has been made aware recently that due to manufacturing tolerances, the fuel line may become damaged after a period of time on Audi S6, RS 6 and S7 vehicles manufactured within a specific period.

2008–2011 AUDI A1 & A3

Due to electrolysis, the DSG transmissions are susceptible to conductive deposits forming in the gearbox control units, possibly causing the gearbox fuse to blow. Should this happen, the clutch will fully open due to power supply failure, causing the vehicle to roll to a stop if in motion.

0 AUDI Q5 (8R)

At temperatures below -20 degrees celsius, the glass-sliding sunroof may suddenly break.

0 AUDI A3

Leaks may occur in the high-pressure fuel lines due to faulty pipe material.

0 AUDI R8 Spyder

There is the possibility that the fuel supply line can come into contact with the heat shield in the engine compartment. This could cause damage to the fuel supply line, which in isolated cases, can lead to leaks.

0 AUDI Q5

Audi AG, having learned that on their QF Model vehicles manufactured within a defined period there is the possibility that, in the event of an accident resulting in the deployment of the curtain airbags, the A-pillar trim comes loose.

0 AUDI A3, TT

There is a possibility that the control unit in the Direct Shift Gearbox (DSG) can cause a false temperature signal indicating that the clutch is overloaded. If this should happen, the control unit will open the clutch in order to protect the gearbox. As a consequence, the clutch protection function is activated, resulting in flashing gear-change indicator, uneven transmission of power, reduced engine torque and release of clutch.

0 AUDI TT

In the event of an accident in which the seat belt tensioners are triggered, the rear side pillar trim can come loose at the front mounting. The trim would then move into the passenger compartment in an uncontrolled manner, causing in increased injury risk for both the front and the rear passengers.

0 AUDI A6 Avant

In isolated cases the power-operated tailgate on vehicles may close unexpectedly and abruptly, shortly after being opened using the power function.

0 AUDI A6 (4F)

A condition exists on some of the vehicles, which in exceptional circumstances and due to inappropriate software programming of the airbag deployment trigger sensor, may, in a worst case situation delay the deployment of both front driver and passenger airbags in the event of an accident.

0 AUDI A8

There is the possibility that in isolated cases the driver's airbag may not deploy as intended if triggered in an accident.

0 AUDI A3

There is a possibility that in isolated cases a gradual loss of gas can occur in the gas generator for the curtain airbags, thereby causing the airbag not to inflate when required.

0 AUDI A8 vehicles with Michelin 255/35 R20 tyres

Tyres can have a sudden loss of pressure.

0 AUDI A4 Cabriolet, S4 Cabriolet Model

Audi AG, having found that there is the possibility that the brightness of these Xenon headlamps fitted to above mentioned Audi models may reduce significantly over time, in the interest of customer satisfaction and possible long term vehicle safety, is voluntarily initiating this vehicle safety recall campaign in Australia to replace the reflectors of both headlamps fitted on these vehicles.

0 AUDI A4, A6, A8

There is a possibility of damage occurring in the sealing rubber boots on the front suspension track control link ball joints fitted to certain A4/A6 and A8 vehicles produced up to 31 December 1999 which if left unrectified, could lead to ingress of moisture.

0 AUDI A3, A4/B6, A6, C5 Allroad and TT

In the event of an accident with a collision impact above the triggering threshold of the airbags, it is possible that the driver's airbag may not deploy as intended.

0 AUDI C5 Allroad

May have been provided with a tyre placard bearing an incorrect tyre designation.

0 AUDI (Various)

Labels provided on lever type jacks, as well as relevant Owner's Manual Instructions supplied in new model Audi vehicles in Australia since 1992, did not fully comply with the labelling requirements of the mandatory Australian Standard AS/NZS:2693/1993.

0 AUDI A3 (Fitted with ABS)

There is a risk that an electrical fault in the ABS control unit can possibly cause overheating of certain components which in some cases could lead to fire.

0 AUDI S3 Quattro, TT Quattro

There is a potential for moisture to enter the ball joints on the rear axles which can start corrosion inside the ball joints thus possibly leading to seizure of the ball joints themselves.

0 AUDI A3

Possible failure of front seat belt buckles in the event of a head on collision.

0 AUDI A3, A4

The Wheel Retaining Bolts May Not Be Compatible With The Wheel And The Wheel, As A Consequence, May Loosen And Could Come Off.

0 AUDI A4, A6, A8

The Protective Rubber Seals That Form Part Of The Steering Track Rod May Be Incomplete And May Allow Water And Debris To Enter The Track Rod Thus Possibly Causing Premature Wear.

0 AUDI A3

A Remote Possibility Exists That Hot Particles, Resulting From Triggering Of The Rear Seat Belt Pyrotechnic Seat Belt Tensioners (in The Event Of A Severe Accident) Could Cause The Covers Of The Belt Tensioners To Ignite.

0 AUDI A4

A Bolt Retaining The Clutch And Pedals May Not Have Been Sufficiently Tightened - Could Cause Loss Of Braking Control.

0 AUDI A3

Under Bonnet Insulator Pad May Foul The Throttle Body Linkage Mechanism Preventing The Linkage From Returning Upon Release Of The Accelerator Pedal.

0 AUDI A3

Possibility That Installed Retractor Mounting Brackets May Develop Vibration Related Fatigue Cracks, Thus Not Affording The Same Degree Of Protection Under Extreme Load Conditions.

0 AUDI A4, A6, A8

Possibility That Engine Misfiring Can Result In Damage To Air Grid In The Air Mass Meter Which Could Cause The Said Grid To Detach And Jam The Throttle Valve.

0 AUDI Coupe 1995; Audi 80 1995; Cabriolet 1995; A4 1995; A6 1995; A8 1995; A4 1996; A6 1996; A8 1996.

The Drivers Side Airbag May Deploy Inadvertently Under Certain Conditions.

0 AUDI 80, A4, A6. A8

Static Electricity In The Steering Wheel Housing Which Can Occur In Certain Weather Condition, May Cause The Airbag To Deploy Inadvertently.,

0 AUDI A4

Possibility Of A Horn Malfunction.

0 AUDI 44 to 4C

Possible Malfunction In The Cruise Control Linkage Due To A Plastic Bush Becoming Brittle.

0 AUDI 100

Brake Failure May Occur If The Vacuum System Is Not Modified.

0 AUDI 200

Rubber Seal Rings On Fuel Injectors May Leak Resulting In Fuel Escaping Into Engine And Ignited On Exhaust System.

0 AUDI 200

If Fuel Tank Is Overfilled Fuel Vapour May Escape From Charcoal Canister & Ignite On Exhaust System.

0 AUDI 200

The Rear Brake Calipers May Not Fully Release & Cause Brake Failure.