Search Recalls
Search by VIN, keyword, make, or filter by recall type, year, and vehicle category.
Search results
871 recalls found
REC-001515
active0 YAMAHA YZF-R3A, MT03LA
The clutch pressure plate bearing may fail when operated frequently. The oil pump drive gear may break due to excessive stress.
Motorcycle
29 June 2016
REC-003721
active0 BRAAAP SS125
The ADR83 Stationary noise test information sticker is not displayed on the motorcycle.
Motorcycle
28 June 2016
REC-003719
active0 BRAAAP ST-250
It is a mandatory requirement that a motorcycle must have each mechanical component accurately stamped and displayed for identification purposes according to regulation for ADR compliance. The following parts have been incorrectly stamped for identification purposes; • Fuel Tap • Rear Master Cylinder Cap • Tail light assembly • The ADR83 stationary noise test information sticker is not displayed
Motorcycle
28 June 2016
REC-003718
active0 BRAAAP URBAN
The ADR83 Stationary noise test information sticker is not displayed on the motorcycle.
Motorcycle
28 June 2016
REC-003720
active0 BRAAAP MOTO3
The ADR83 stationary noise test information sticker is not displayed on the motorcycle.
Motorcycle
28 June 2016
REC-000265
active2013-2014 DUCATI 1100 SUPERLEGGERA
Due to a potential fault in the clutch assembly, one of the clutch components may break, increasing the risk of rear wheel lock up during use of the bike.
Motorcycle
21 June 2016
REC-000264
active2015-2016 DUCATI Xdiavel
It is possible that the rear wheel rim might have been installed in the wrong way, with the 4 rear wheel shaft driving pins inserted in the slots rather than in the 4 relevant holes.
Motorcycle
20 June 2016
REC-005081
active2016 HUSQVARNA FC 250
Quality deviations in the production process of the connecting rod may result in early failure and fracturing of the conrod under certain load conditions. This issue is identified to a specific vin range of FC 250 2016 vehicles in Australia.
Motorcycle
24 May 2016
REC-005082
active2016 KTM 250 SXF Factory Edition & 250 SXF
Quality deviations in the production process of the connecting rod may result in early failure and fracturing of the conrod under certain load conditions. This issue is identified to a specific vin range of 250 SXF Factory Edition vehicles in Australia.
Motorcycle
24 May 2016
REC-000368
active2013-2016 HARLEY DAVIDSON DYNA LOW RIDER
The ignition switch may become damaged internally due to engine induced vibration.
Motorcycle
19 May 2016
REC-000801
active2015-2016 KTM SUPER ADVENTURE
There may be an oil leak at the plug connection, and software for the semi active shock requires updating.
Motorcycle
5 May 2016
REC-000749
active0 KAWASAKI Ninja 250R, Ninja 250RSE, Versys 650L ABS, ER-6nL ABS
On some units, the circlips securing the passenger footrest pivot pins may be brittle due to a manufacturing defect.
Motorcycle
18 Apr 2016
REC-003687
active0 TRIUMPH STREET TWIN D-SERIES & BONNEVILLE T120
The motorcycles may have been installed with faulty fuel tank sub harnesses.
Motorcycle
6 Apr 2016
REC-003682
active0 KAWASAKI ZX1000RGFA, ZX1000SGF/SGFA/SGFB
The steering damper bracket mounting bolts could break due to over tightening during assembly.
Motorcycle
7 Mar 2016
REC-001361
active2014-2016 VICTORY INTERNATIONAL CRUISER
The noise levels may not meet the regulatory requirements when the affected motorcycle is ridden under normal conditions.
Motorcycle
6 Mar 2016
REC-000556
active0 Honda NSS300
Due to a manufacturing defect, one of the securing nuts on the Rear Brake Hose Flange may not be tightened to the correct specification.
Motorcycle
26 Feb 2016
REC-000756
active2011-2015 KAWASAKI various, see file for list
Improper routing of electrical wires under the fuel tank may cause the leads come in contact with frame edge. In addition, on certain models (JKBEJCA1?A000108 - JKBEJCA1?A015716), the throttle body holder may harden because of insufficient heat resistance. If it is continuously used the throttle body holder may crack and additional air may flow into the engine.
Motorcycle
28 Jan 2016
REC-001236
active0 SUZUKI VARIOUS MOTORCYCLES
The regulator/rectifier power module circuit board may have absorbed moisture during storage in highly humid conditions. This may have reduced the strength of the adhesive used to affix the circuit board to the aluminium case. The heat generated from the power module can cause the power module to lift from the case.
Motorcycle
15 Jan 2016
REC-000558
active0 Honda VT750C - 750cc, Cruiser
Due to the fixing method for the Bank Angle Sensor wiring harness, the wiring may bend and break after prolonged usage.
Motorcycle
5 Jan 2016
REC-005085
active2015 HUSQVARNA 125, 250 TC & 250, 350, 450 FC
Due to variations in the spoke manufacturing process, some spokes on the front wheel may exhibit quality deviations. Depending on where they are fitted in the wheel, care and spoke tension, it is possible that individual spokes may break while riding. This can overload the remaining intact spokes and consequently break them.
Motorcycle
22 Dec 2015